|płatność||L/C, D/A, D/P, Western Union, MoneyGram, T/T, Paypal|
|Znamionowe napięcie wejściowe||1PH ~ 230V ± 15%|
|Znamionowe wyjście||250A / 20V|
|Maksymalne napięcie obwodu otwartego||7,81 KVA|
|Napięcie otwartego obwodu||70V ~ 80V|
|Gwarancja||1 rok gwarancji|
|Wymiary||490 x 230 x 440 mm|
The total solution of TIG welding
Input Power: 200-240V, 1-Phase
Conventional Pulsed TIG
Typically from 0.2 to 10 PPS. Provides a heating and cooling effect on the weld puddle and can reduce distortion by lowering the average amperage. This heating and cooling effect also produces a distinct ripple pattern in the weld bead. The relationship between pulse frequency and travel speed determines the distance between the ripples. Slow pulsing can also be coordinated with filler metal addition and can increase overall control of the weld puddle.
High Speed Pulsed TIG
In excess of 40 PPS, Pulsed TIG becomes more audible than visible—causing increased puddle agitation for a better as-welded microstructure. Pulsing the weld current at high speeds — between a high Peak and a low Background amperage — can also constrict and focus the arc. This results in maximum arc stability, increased penetration and increased travel speeds.
The Standard Square Wave offers fast transitions between EN and EP for a responsive, dynamic, and focused arc with better directional control. It forms a fast-freezing puddle with deep penetration and fast travel speeds.
The Sine Wave a soft arc with the feel of a conventional power source. It provides good wetting action and actually sounds quieter than other waves. Its fast transition through the zero amperage point also eliminates the need for continuous high frequency.
Features of MIX TIG:
The AC current can get a very good clearance, and DC current can get a deeper penetration.
Use the MIX TIG we can get an excellent Arc Concentration,
can be carried out the excellent welding performance from thin to thick plate.
1) Nice weld appearance, deep penetration.
2) Excellet Arc Concentration..
3) Substantially reduce the electrode consumption.
MIX TIG Frequency (Hz):
the cycle time of MIX
TIG in 1 second. Adjustable range: 0.1-10Hz.
MIX TIG Balance (DC) %:
DC Balance (%) = (tad/Tmix) x 100
Controls the width of the Controls the width of the arc cone.
Increasing the AC Frequency provides a more focused arc with increased directional control.
Note: Decreasing the AC Frequency softens the arc and broadens the weld puddle for a wider weld bead.
AC Balance Control
Controls arc cleaning action. Adjusting the % EN of the AC wave controls the width of the etching zone surrounding the weld.
Note: Set the AC Balance control for adequate arc cleaning action at the sides and in front of the weld puddle. AC Balance should be fine tuned according to how heavy or thick the oxides are.
Adjusts the ratio of EN to EP amperage to precisely control heat input to the work and the electrode.
EN amperage controls the level of penetration, while EP amperage dramatically effects the arc cleaning action along with the AC Balance control.
|Rated Input Voltage||1PH ~ 230V ±15%|
|Max. Load Power Capacity||TIG: 7.81KVA|
|Rated Duty Cycle(40℃) 60%||TIG: 250A/20V|
|Welding Current/Voltage Range||TIG: 5A/10.2V~250A/20V|
|Open Circuit Voltage||70V~80V|
|TIG Pulse Peak Current||5A~250A|
|TIG; Pulse Pulse Frequency||0.2Hz~200Hz|
|TIG; Pulse Pulse Width (Ratio)||1~100%|
|TIG; AC TIG AC Frequency Range||20Hz~250Hz|
|TIG; AC TIG AC Clean Width (AC Balance)||+40~-40|
|TIG; AC TIG AC Clean Ratio (AC Bias) %||+30~-50|
|TIG; MIX TIG MIX Frequency||1Hz~5Hz|
|TIG; MIX TIG DC Balance (%)||20~80|
|TIG; Arc-starting Current||5A~250A|
|TIG; Crater-filling Current||5A~250A|
|TIG; Current Up-slope Time||0.1S~15S|
|TIG; Current Down-slop Time||0.1S~15S|
|TIG; Pre-Gas Time||0.1S~15S|
|TIG; Flow-Gas Time||0.1S~15S|
|TIG; Spot Arc Time||0.1S~10S|
|MMA Arc Force||10A~200A|
|MMA Hot Start Time||0.1~3S|
|MMA Hot Start Current||10A~200A|
|Water-cooling Unit: WC-100|
|Operating Voltage||230V 50/60Hz|
|Recommended Cooling Liquid||20%~40% ethanol/water|
A: We are factory with more than 10 years manufacturing experience and we provide perfect OEM and after-sale service.
A: We accept T/T, Western Union, Alibaba Trade Assurance payments. For those orders less than 1000USD, we accept PayPal to pay.
A: We offer 3-year product life guarantee ,and a generous 1 year warranty on al purchases that begins with the bill of lading.
A: For every model of machine, it has a CE certificate.
A: We usually quote within 24 hours after we get your inquiry. If you are urgent to get the price,please send the message on trade management or call us directly